e-ManualTopSite mapHelpGlossary

Category Top

Clearing Paper Jams

Locations of Paper Jams

Main Unit

Right Cover of the Machine

Right Cover of the Machine (When the Multi-drawer Paper Deck-A1 is attached)

Left Cover of the Machine

Left Cover of the Machine (When the Buffer Pass Unit-J1 is attached)

Fixing Transport Unit

Paper Sources

Multi-purpose Tray

Paper Drawers 3 and 4

Paper Drawers (Right/Left)

Paper Deck Unit-C1/POD Deck Lite-A1 (Optional)

Front Cover of the Multi-drawer Paper Deck-A1 (Optional)

Paper Decks of the Multi-drawer Paper Deck-A1 (Optional)

Duplex Color Image Reader Unit-F1 (Optional)

Buffer Pass Unit-J1

Document Insertion Unit-H1 (Optional)

Professional Puncher Integration Unit-B1 (Optional)

Paper Folding Unit-G1 (Optional)

Staple Finisher-K1 (Optional)

Booklet Finisher-K1 (Optional)

Inside the Front Cover

Saddle Stitcher Unit

Document Insertion/Folding Unit-G1/Document Insertion Unit-J1 (Optional)

Insertion Unit

Inside the Insertion Unit

Folding Unit

External 2/3 Hole Puncher-A1 (Optional)

Staple Finisher-L1/Booklet Finisher-L1 (Optional)

Inside the Top Cover

Output Area

Front Cover of the Booklet Finisher-L1

Saddle Stitcher Unit of the Booklet Finisher-L1

Reducing the Frequency of Paper Jams

Clearing Staple Jams (For Optional Products)

Locations of Staple Jams

Stapler Unit of the Staple Finisher-K1/Booklet Finisher-K1

Saddle Stitcher Unit of the Booklet Finisher-K1

Staple Finisher-L1/Booklet Finisher-L1

Saddle Stitcher Unit of the Booklet Finisher-L1

If Memory Becomes Full During Scanning

If OCR (Text Searchable) Performs Inadequately

Printer/Fax Driver Troubleshooting

Service Call Message

List of Error Messages

General

Fax

Scan and Send

Scan and Store/Access Stored Files

Quick Menu

Printer

Network/Security

MEAP

User Setting Information Management

List of Error Codes without Messages

Top » Problem Solving » Clearing Staple Jams (For Optional Products) » Saddle Stitcher Unit of the Booklet Finisher-K1
Saddle Stitcher Unit of the Booklet Finisher-K1
08JK-0R8
Check the location of the staple jam, and follow the procedure described below, while referring to the directions that appear on the touch panel display, to remove the jammed staple.
IMPORTANT
Take care when handling the optional equipment that is attached to the machine. When an optional unit's cover is opened to replace a staple cartridge, discard the punch waste, discard the trim waste, discard the staple waste, or clear paper or staple jams, prints may still be output if other optional units are operating normally, and are not involved in the paper or staple jam removal procedure.
Before clearing the staple jam, remove all output sheets from the booklet tray.
NOTE
The Booklet Finisher-K1 is an optional product.
If a paper jam occurs at the same time as a staple jam, remove the jammed paper before removing the jammed staples.
1.
Open the front cover of the finisher.
2.
Pull out the staple case from the saddle stitcher unit (F-C5).
1. Pull out the saddle stitcher unit (F-C5).
2. Pull out the staple case.
3.
Hold the staple case by its left and right sides, and lower the bracket on the staple case.
4.
Remove the jammed and exposed staples from the staple case.
5.
Return the bracket on the staple case to its original position.
6.
Return the staple case to its original position in the saddle stitcher unit.
When returning the staple case, always make sure to the staple case is inserted until the arrows are aligned as shown in the diagram.
7.
Push the saddle stitcher unit (F-C5) back into the machine, and close the front cover of the finisher.
1. Gently push the saddle stitcher unit back into the machine.
Always make sure to push the saddle stitcher unit in as far as it can go.
2. Close the front cover of the finisher.
CAUTION
When returning the saddle stitcher unit and closing the cover, be careful not to get your fingers caught, as this may result in personal injury.
Back to Top