e-ManualTopSite mapHelp

Category Top

What This Machine Can Do

The Touch Panel Display

Setting the Main Menu Screen

Shortcut to Settings/Registration

Setting Each Function Screen

Touch Panel Key Display

Adjusting the Brightness of the Touch Panel Display

Adjusting the Position and Angle of the Touch Panel Display

Entering Characters from the Touch Panel Display

Entering Characters Using a USB Keyboard

Entering the Department ID and PIN

Login Service

Placing Originals

Platen Glass

Feeder

Loading Paper into the Stack Bypass-B1

Loading Envelopes into the Stack Bypass-B1

Loading Paper with the Stack Bypass Alignment Tray-C1

Available Paper Stock

Inserting and Removing Memory Media

Tone Settings

Energy Saving Features

Checking the Counter and Controller Version

Conveying Messages Using the Message Board

Remote Operation

Other Useful Functions

Adding New Functions

Installing System Options/MEAP Applications (Delivery)

Installing System Options/MEAP Applications (Manual)

Displaying the Installation Log

Performing a Communication Test With the Delivery Server

Updating Firmware

Printing Reports

Counter Report

PAGE COUNT LIST

PRINT LOG LIST

DEVICE INFORMATION DELIVERY DESTINATION LIST

DEVICE INFORMATION COMMUNICATION LOG REPORT

SEND JOB LIST

TX REPORT

FAX TX REPORT/FAX ERROR TX REPORT

FAX MULTI TX REPORT

COMMUNICATION MANAGEMENT REPORT TX/RX

FAX ACTIVITY REPORT TX/RX

Forwarding Conditions List

Registered LDAP Server List

ADDRESS LISTS

Store Log Report

User Data List

System Information

Mail Box File List

IPSec Policy List

Printer Report

Initialize All Data/Settings Report

Top » Basic Operations » Loading Paper into the Stack Bypass-B1 » Loading Paper with the Stack Bypass Alignment Tray-C1
Loading Paper with the Stack Bypass Alignment Tray-C1
0L3X-01F
By using the Stack Bypass Alignment Tray-C1, you can reduce the amount of skew of paper (i.e. paper is transported diagonally) which is fed from the Stack Bypass-B1, and prevent the image misalignment.
To set the positions of the paper alignment guides, follow the procedure described below to stabilize the paper alignment guides.
NOTE
The Stack Bypass Alignment Tray-C1 is an optional product.
1.
Slightly widen the slide guides of the Stack Bypass-B1 to match the width of the loaded paper.
2.
Loosen the fixing roulette screws.
Loosen the four fixing roulette screws at the front and the back.
3.
Slightly widen the paper alignment guides to match the width of the loaded paper.
4.
Fan the paper several times, and then align the edges by pushing the protruding edges in with your fingers.
CAUTION
Take care not to cut your hands on the edges of the paper.
IMPORTANT
If the paper is curled, straighten out curled paper prior to use, as shown below.
Straighten out a stack of paper as shown in the illustration below.
Curled Paper
Straightened Paper
5.
Load the paper into the Stack Bypass Alignment Tray-C1.
IMPORTANT
Make sure that the height of the paper stack does not exceed the loading limit mark ().
NOTE
Up to 100 sheets (17 lb bond (64 g/m2)) of paper can be loaded into the Stack Bypass Alignment Tray-C1.
6.
Adjust the sliding guides of the Stack Bypass-B1 to match the size of the paper.
7.
Adjust the paper alignment guides to match the size of the paper loaded in the Stack Bypass Alignment Tray-C1.
Leave no space between the stack of paper and the guides.
8.
Repeat steps 5 and 6 once or twice, and align the sliding guide of the Stack Bypass-B1 with the paper alignment guide to match the size of the paper.
IMPORTANT
To prevent the copied images from being slanted or misaligned, make sure that the edges of the stack of paper are neatly aligned in steps 5 and 6.
9.
Tighten the fixing roulette screws to stabilize the paper alignment guide.
Tighten the four fixing roulette screws at the front and the back.
For information on how to select the paper type and paper size, follow the procedure from step 4 in "Loading Paper into the Stack Bypass-B1."
Back to Top