<Saddle Stitch Staple Repositioning>

You can reposition the stapler of the saddle stitcher unit after clearing a staple jam, or after replacing the staple cartridge. Saddle stitch staple repositioning works by feeding several sheets of paper into the saddle stitcher unit and stapling them together.

<Change Fold/Stitch Position>

If you are using the Saddle Stitch mode of the Booklet Finisher, and you notice that the saddle stitch position of the paper is not exactly in the middle of the booklet, you can make adjustments to the saddle stitch position to compensate for this error. Adjusting the Saddle Stitch Position

<Adjust Saddle Stitch Fold Position>

If you are using the Saddle Stitch mode of the Booklet Finisher, and you notice that the folds of the paper are not exactly in the middle of the booklet, you can make adjustments to the saddle stitch fold placement to compensate for this error. This mode enables you to adjust the folding position without changing the stapling position. Adjusting the Saddle Stitch Folding Position

-2.00 mm to 0.00 mm to +2.00 mm, in 0.25 mm increments

<Adjust Double Staple Width>

You can adjust the double staple width.

When the Staple Finisher-W1 PRO or Booklet Finisher-W1 PRO is attached
4 3/4" to 5 7/8"

When the Staple Finisher-X1 or Booklet Finisher-X1 is attached
<4_3/4">, <5_11/16">

<Switch Finisher Puncher Mode>

You can set whether to give priority to the punching speed or to precision.

<Speed Priority>, <Precision Priority>

<Speed/Precision Priority for Double Staple>

You can set whether to give priority to the double stapling speed or to precision.

<Speed Priority>, <Precision Priority>

<Adjust Trim Width>

You can adjust the trimming width of Saddle Stitch printouts in 0.01" increments. When using the optional Booklet Trimmer-D1, also see the included instruction manual for more information.

0.08" to 0.78", in 0.01" increments

You can adjust the folding positions of the paper when a folding mode such as C-fold or Z-fold is set.

<Alignment Adjustment When Stapling>

The copied or printed paper may shrink because of temperature, humidity, or a characteristic of the paper type. In this case, this mode enables you to align copied or printed papers by adjusting the position of the alignment guide inside the finisher so as to staple the aligned papers.

-3.0 mm to 0.00 mm to +3.0 mm, in 0.1 mm increments

<Finisher Tray A Alignment Adjustment>

You can adjust paper alignment when outputting to Tray A of a finisher. Adjusting Paper Alignment

-3.0 mm to 0.00 mm to +3.0 mm, in 0.1 mm increments

<Finisher Tray B Alignment Adjustment>

You can adjust paper alignment when outputting to Tray B of a finisher. Adjusting Paper Alignment

-3.0 mm to 0.0 mm to +3.0 mm, in 0.1 mm increments

<Finisher Output Priority Settings (Heavy 1-4)>

You can give priority to productivity or alignment for the output paper when using <Heavy 1>, <Heavy 2>, <Heavy 3>, or <Heavy 4>.

<Productivity Priority>, <Alignment Priority>

<Finisher Output Priority Settings (Heavy 5, 6)>

You can give priority to productivity or alignment for the output paper when using <Heavy 5> or <Heavy 6>.

<Productivity Priority>, <Alignment Priority>

<Finisher Output Priority Settings (Thin)>

You can give priority to productivity or alignment for the output paper when using thin paper.

<Precision Priority>, <Alignment Priority>

<Time Until Stapling Starts in Stapler Mode>

You can set the time to start stapling after the paper is inserted in the slit when you use manual stapling. For more information about manual stapling, see Optional Equipment.

1 to 3 to 5 seconds