e-ManualTopSite mapHelp

Category Top

Loading Paper

Loading Paper into a Paper Deck (Main Unit, POD Deck-D1 (Optional))

Adjusting a Paper Deck to Hold a Different Paper Size (Main Unit, POD Deck-D1 (Optional))

Loading Pre-Punched Paper

Loading Transparency/Clear/Translucent Film

Loading Tab Paper

Loading Paper into the POD Deck Lite-C1 (Optional)

Loading Paper into the LONG SHEET TRAY-A1 (Optional)

Loading Paper into the Document Insertion Unit-N1 (Optional)

Replacing the Staple Cartridge (For Optional Products)

Replacing the Staple Cartridge in the Stapler Unit (Finisher-AN1/Saddle Finisher-AN2)

Replacing the Staple Cartridge in the Saddle Stitcher Unit (Saddle Finisher-AN2)

Removing Staple Waste (Finisher-AN1/Saddle Finisher-AN2)

Removing Punch Waste (Puncher Unit-BS1/Puncher Unit-BT1)

Operating the Limited Functions Mode

Replacing Cleaning Web Unit

Replacing the Toner Cartridge

Replacing the Waste Toner Container

Routine Cleaning

Originals Cannot Be Scanned Properly (Cleaning the Platen Glass)

Originals Cannot Be Scanned Properly (Cleaning Method of the Original Scanning Area)

Scanned Originals Become Dirty (Manual Feeder Cleaning)

Scanned Originals Become Dirty (Automatic Feeder Cleaning)

Output Paper Becomes Dirty (Cleaning Inside of the Main Unit)

Output Paper Becomes Dirty (Wire Cleaning)

Output Paper Becomes Dirty (Roller Cleaning)

Streaks and Gloss Unevenness Appear on Output Paper (Refreshing the Fixing Roller)

Streaks and Gloss Unevenness Appear on Output Paper (Adjusting the Fixing Roller Auto Refresh Level)

Cleaning the Touch Panel Display

Consumables

Top » Maintenance » Operating the Limited Functions Mode
Operating the Limited Functions Mode
0S9Y-08K
If a specific message (the service call message) appears on the display, operate the Limited Functions Mode.
If you set the Limited Functions Mode to 'On', the machine stops using the specific function that has a malfunction, and you may make copies/prints using other functions that can operate normally.
IMPORTANT
Call your service representative before you operate the module separation switch.
E590
Cause:
The Puncher Unit-BS1 or Puncher Unit-BT1 is out of order.
Remedy:
You can make copies/prints using functions other than the hole punch function by operating the Limited Functions Mode.
E514, E530, E531, E532, E535, E537, E539, E540, E542, E566, E567, E568, E577, E578, E57a, E57b, E57c, E585
Cause:
The Finisher-AN1 or Saddle Finisher-AN2 is out of order.
Remedy:
You can only output copies/prints by operating the Limited Functions Mode to restrict all of the functions for the finisher such as staple and collate.
E503-8004, E5a7, E5af, E5f0, E5f1, E5f2, E5f3, E5f4, E5f6, E5fa, E5fb, E5fc, E5fd, E5fe, E5ff
Cause:
The saddle stitcher unit of the Saddle Finisher-AN2 or the Booklet Trimmer-D1 is out of order.
Remedy:
You can make copies/prints using functions other than the saddle stitch function by operating the Limited Functions Mode.
E518, E562, E569, E56a, E56b, E56e
Cause:
The Paper Folding Unit-J1 is out of order.
Remedy:
You can make copies/prints without using the folding mode by operating the Limited Functions Mode.
E5a1, E5a2, E5a3, E5a4 (excluding Detailed Code 85h), E5a5, E5a8, E5a9, E5aa (excluding Detailed Code 07h), E5ab, E5ac, E5ad, E5ae, E5b0 (excluding Detailed Code 13h), E5b2, E5b4, E5b5, E5b6, E5b8, E5b9, E5bd, E5c0, E5c1, E5c2, E5c3, E5c4, E5c5 (excluding Detailed Code 08h), E5c6, E5c7, E5d0, E5d1, E5d2 (excluding Detailed Code 05h), E5d4, E5d6 (excluding Detailed Code 06h), E5d7 (excluding Detailed Code 06h), E5d8, E5d9
Cause:
The Perfect Binder-E1 is out of order.
Remedy:
You can make copies/prints using functions other than the Perfect Binding mode by operating the Limited Functions Mode.
NOTE
After setting the Limited Functions Mode to 'On', the corresponding function will be grayed out on the display, and cannot be used.

1.
Press (Settings/Registration).
2.
Press [Management Settings] → [Device Management] → [Limited Functions Mode].
NOTE
For instructions on setting the Limited Functions Mode from the Service Call Message screen, see "Setting the Limited Functions Mode from the Service Call Message Screen."
3.
Select the finishing mode you want to limit.
4.
Select [On] or [Off] → press [OK].
5.
Press [Close].
NOTE
The Limited Functions Mode is enabled only after you restart the machine (the main power is turned OFF, and then back ON). For instructions on restarting (turning the main power OFF, and then back ON) the machine, see "Main Power and Energy Saver Key."