<Preferences> <Timer/Energy Settings><Timer/Energy Settings>
This section describes the timer settings and energy settings.
<Adjust Time>
<Preferences> <Timer/Energy Settings>You can adjust the time in minutes.
 |
|
Even if you change the time from 23:59 to 00:00, the date will not be changed.
|
Date/Time Settings
<Preferences> <Timer/Energy Settings>Setting the current date and time is very important. For instructions on how to configure the setting, see Setting the Date/Time.
<Time Format>
<Preferences> <Timer/Energy Settings>You can set whether to display the time in 24-hour notation or 12-hour notation.
<Quick Startup Settings for Main Power>
<Preferences > <Timer/Energy Settings>If you set this function to <On>, you can reduce the time it takes until you can perform operations on the screen and scan originals after the power is turned ON.
|
|
|
When this function is enabled
Standby power is consumed even when the power is turned OFF
A tone sounds when turning the power ON/OFF. (However, the machine may not be able to start up quickly and the tone may not sound, depending on the status of the machine.)
Even if this function is set to <On>, the machine does not startup quickly in the following situations:
When any of the network settings below are set to <On>
AppleTalk
Wi-Fi
Bluetooth
When turning ON the main power of the machine after turning OFF the main power in any of the conditions below
More than 110 hours have elapsed after quick startup
Operating jobs
Jobs are reserved
Just after using telephone lines
Backing up data
Accessing to the machine via network
After specifying settings which require restarting the machine
Error is occurred
Using the Limited Functions mode
The power cord is disconnected after turning OFF the main power
MEAP applications which do not support quick startup are installed on the machine
When turning ON the main power of the machine in 20 seconds after turning OFF the main power
When turning ON the main power of the machine after eight hours have passed since the machine was turned OFF
When turning ON the main power of the machine after turning OFF the main power from the Remote UI
|
<Auto Reset Time>
<Preferences> <Timer/Energy Settings>You can specify the time period in which you are logged out and the touch panel display returns to the default setting automatically.
<Restrict Auto Reset Time>
<Preferences> <Timer/Energy Settings>If you set this function to <On>, general users become unable to set <Auto Reset Time> and <Function After Auto Reset>.
<Function After Auto Reset>
<Preferences> <Timer/Energy Settings>You can set whether the default screen set for <Default Screen after Startup/Restoration> in <Preferences> or the immediately previous screen is displayed at startup after the Auto Reset initiates.
|
|
|
If you select <Initial Function>, the screen set in <Default Screen after Startup/Restoration> is displayed when the Auto Reset initiates. If you select <Selected Function>, the Basic Features screen for the function you were using is displayed again.
|
<Auto Sleep Time>
<Preferences> <Timer/Energy Settings>You can set the time until the machine automatically enters the Sleep mode if no operations are performed.
|
|
|
It is recommended that the default value is used for this setting.
|
<Sleep Mode Energy Use>
<Preferences> <Timer/Energy Settings>You can set the amount of energy that the machine consumes when it is in the Sleep mode.
 |
|
If the machine is connected to a computer using a USB cable, depending on the timing for entering the sleep mode, the machine may be unable to receive data correctly. Reactivate the machine from the sleep mode, then execute the job again.
The energy consumption level may be the same as when <High> is set even when <Low> is set, depending on the status of the machine.
|
|
|
|
When performing wireless communication while <Sleep Mode Energy Use> is set to <Low>, and <Wireless LAN Settings> or <Use Bluetooth> is enabled, <Compensate for Network Comm.> changes to <On>.
If the energy consumption level is set to <Low>, communication failure may occur, depending on the network utility software you are using. To avoid this, press the Energy Saver key to cancel the Sleep mode before using the machine.
|
<Auto Sleep Weekly Timer>
<Preferences> <Timer/Energy Settings>You can set the time that the machine automatically enters the Sleep mode each day of the week.
|
|
|
If you set both the <Auto Sleep Time> and <Auto Sleep Weekly Timer>, the <Auto Sleep Time> setting is given priority.
|
<Time Settings for Auto Adjust Gradation>
<Preferences> <Timer/Energy Settings>You can automatically perform the automatic gradation adjustment at a set time every day.
<Sleep Mode Exit Time Settings>
<Preferences> <Timer/Energy Settings>You can set the time for recovering from the Sleep mode.
<Sleep Mode Eco Exit>
<Preferences> <Timer/Energy Settings>When you cancel sleep mode and start the operation, you can activate necessary functions sequentially. The control panel is activated first, followed by other functions activated in response to the user's operations. You can save energy and lower noise by not activating unnecessary functions.
<Use Motion Sensor>
<Preferences> <Timer/Energy Settings>When the motion sensor detects a person near the machine, the machine exits the Sleep mode automatically. You can adjust the accuracy for detecting people by changing the sensor sensitivity.
The following four sensitivity settings are available for <Sensor Sensitivity>. When a user stays in the detection area longer than a certain period of time, the machine exits the Sleep mode.
|
Sensitivity Setting
|
Sensitivity Level
|
|
Low
|
With this sensitivity level, the machine does not recover even if someone passes by slowly.
|
|
Standard
|
With this sensitivity level, the machine does not recover even if someone passes by at a regular speed.
|
|
Slightly High
|
With this sensitivity level, the recovery speed is prioritized more than the "Standard" level.
|
|
High
|
With this sensitivity level, the recovery speed is given top priority.
|