e-ManualTopSite mapHelp

Category Top

Loading Paper

Loading Paper into a Paper Deck (Main Unit, POD Deck-D1 (Optional))

Adjusting a Paper Deck to Hold a Different Paper Size (Main Unit, POD Deck-D1 (Optional))

Loading Pre-Punched Paper

Loading Transparency/Clear/Translucent Film

Loading Tab Paper

Loading Paper into the POD Deck Lite-C1 (Optional)

Loading Paper into the LONG SHEET TRAY-A1 (Optional)

Loading Paper into the Document Insertion Unit-N1 (Optional)

Replacing the Staple Cartridge (For Optional Products)

Replacing the Staple Cartridge in the Stapler Unit (Finisher-AN1/Saddle Finisher-AN2)

Replacing the Staple Cartridge in the Saddle Stitcher Unit (Saddle Finisher-AN2)

Removing Staple Waste (Finisher-AN1/Saddle Finisher-AN2)

Removing Punch Waste (Puncher Unit-BS1/Puncher Unit-BT1)

Operating the Limited Functions Mode

Replacing Cleaning Web Unit

Replacing the Toner Cartridge

Replacing the Waste Toner Container

Routine Cleaning

Originals Cannot Be Scanned Properly (Cleaning the Platen Glass)

Originals Cannot Be Scanned Properly (Cleaning Method of the Original Scanning Area)

Scanned Originals Become Dirty (Manual Feeder Cleaning)

Scanned Originals Become Dirty (Automatic Feeder Cleaning)

Output Paper Becomes Dirty (Cleaning Inside of the Main Unit)

Output Paper Becomes Dirty (Wire Cleaning)

Output Paper Becomes Dirty (Roller Cleaning)

Streaks and Gloss Unevenness Appear on Output Paper (Refreshing the Fixing Roller)

Streaks and Gloss Unevenness Appear on Output Paper (Adjusting the Fixing Roller Auto Refresh Level)

Cleaning the Touch Panel Display

Consumables

Top » Maintenance » Removing Punch Waste (Puncher Unit-BS1/Puncher Unit-BT1)
Removing Punch Waste (Puncher Unit-BS1/Puncher Unit-BT1)
0S9Y-08H
When the punch waste tray of the Puncher Unit-BS1 or Puncher Unit-BT1 becomes full, an animation screen prompting you to remove the punch waste appears on the touch panel display.
The location of the Finisher-AN1 or Saddle Finisher-AN2 is indicated in the following illustration.
Follow the procedure described below to remove the punch waste.
IMPORTANT
Take care when handling the optional equipment that is attached to the machine. When an optional unit's cover is opened to replace a staple cartridge, discard the punch waste/trim waste/staple waste, or clear paper or staple jams, prints may still be output if other optional units are operating normally, and are not involved in the paper or staple jam removal procedure.
NOTE
When the punch waste tray is full, you cannot make copies or prints using the Hole Punch mode.
The Puncher Unit-BS1 and Puncher Unit-BT1 are optional products.
The Puncher Unit-BS1 and Puncher Unit-BT1 are available only when the Finisher-AN1 or Saddle Finisher-AN2 is attached.
1.
Open the front cover of the finisher.
2.
Pull out the punch waste tray.
NOTE
Check that the guide (F-A2) is closed before pulling out the punch waste tray. If the guide is open, the punch waste tray cannot be pulled out. Close the guide as shown in the illustration below.
3.
Discard the punch waste into a receptacle.
IMPORTANT
Make sure that the punch waste tray is completely emptied.
4.
Return the punch waste tray to its original position.
Always make sure to insert the punch waste tray as far as it can go.
NOTE
If the punch waste tray is not securely in place, you cannot make copies or prints in the Hole Punch mode.
Check that the guide (F-A2) is closed before inserting the punch waste tray. If the guide is open, the punch waste tray cannot be inserted. Close the guide as shown in the illustration below.
5.
Close the front cover of the finisher.
CAUTION
When closing the front cover of the finisher, be careful not to get your fingers caught, as this may result in personal injury.
Back to Top