e-ManualTopSite mapHelp

Category Top

Loading Paper

Loading Paper into a Paper Drawer

Adjusting a Paper Drawer to Hold a Different Paper Size

Loading Envelopes

Loading Pre-Punched Paper

Loading Transparencies/Clear Film

Loading Tab Paper

Loading Paper into the POD Deck Lite-B1 (Optional)

Loading Paper into the Multi-drawer Paper Deck-B1 (Optional)

Loading Paper into the Document Insertion Unit-M1 (Optional)

Replacing the Staple Cartridge (For Optional Products)

Replacing the Staple Cartridge in the Stapler Unit (Finisher-AM1/Saddle Finisher-AM2)

Replacing the Staple Cartridge in the Saddle Stitcher Unit (Saddle Finisher-AM2)

Replacing the Staple Cartridge in the Stapler Unit (Staple Finisher-T1/Booklet Finisher-T1)

Replacing the Staple Case in the Saddle Stitcher Unit (Booklet Finisher-T1)

Removing Staple Waste (Finisher-AM1/Saddle Finisher-AM2)

Removing Punch Waste (Puncher Unit-BS1/Puncher Unit-BT1)

Removing Punch Waste (External 2/3 Hole Puncher-C1/External 2/4 Hole Puncher-C1/External 4 Hole Puncher-C1)

Operating the Limited Functions Mode

Replacing the Toner Cartridge

Replacing the Waste Toner Container

Routine Cleaning

Originals Cannot Be Scanned Properly (Cleaning the Platen Glass)

Originals Cannot Be Scanned Properly (Cleaning Method of the Original Scanning Area)

Scanned Originals Become Dirty (Manual Feeder Cleaning)

Scanned Originals Become Dirty (Automatic Feeder Cleaning)

Output Paper Becomes Dirty (Cleaning Inside of the Main Unit)

Output Paper Becomes Dirty (Wire Cleaning)

Output Paper Becomes Dirty (Roller Cleaning)

Output Paper Becomes Dirty (Belt Cleaning)

Streaks and Gloss Unevenness Appear on Output Paper (Refreshing the Fixing Belt)

Streaks and Gloss Unevenness Appear on Output Paper (Adjusting the Fixing Belt Auto Refresh Level)

Cleaning the Touch Panel Display

Consumables

Top » Maintenance » Replacing the Staple Cartridge (For Optional Products) » Replacing the Staple Cartridge in the Stapler Unit (Staple Finisher-T1/Booklet Finisher-T1)
Replacing the Staple Cartridge in the Stapler Unit (Staple Finisher-T1/Booklet Finisher-T1)
0L3X-0LJ
When the stapler unit of the Staple Finisher-T1 or Booklet Finisher-T1 is almost out of staples and the staple cartridge in the stapler unit must be replaced, an animation screen prompting you to replace the staple cartridge appears on the touch panel display.
The location of the Staple Finisher-T1 or Booklet Finisher-T1 is indicated in the following illustration.
IMPORTANT
Remove the orange seal that holds the staples together after you place the staple cartridge into the staple case.
NOTE
The Staple Finisher-T1 and Booklet Finisher-T1 are optional products.
We recommend that you order staple cartridges from your local authorized Canon dealer before your stock runs out.
Use only staple cartridges intended for use with this machine.
1.
Open the front cover of the finisher.
*1 Booklet Finisher-T1
*2 Staple Finisher-T1 
2.
Pull out the staple case, holding it by the green tab.
3.
Pull out the empty staple cartridge from the staple case.
1. Press the areas indicated by PUSH on both sides of the staple case.
2. Once you have released the spring-loaded case, pull out the staple cartridge.
4.
Insert a new staple cartridge into the staple case.
1. Insert a new staple cartridge.
2. Press the spring-loaded case down until it clicks into place.
3. Remove the seal holding the staples together, by pulling it straight out.
IMPORTANT
Do not remove the seal that holds the staples together before you place the staple cartridge into the staple case.
Only one staple cartridge can be inserted at a time.
Make sure that you pull the seal straight out. If you pull it out at an angle, it may tear.
5.
Gently push the staple case back into the finisher and push down firmly until it is securely in place.
6.
Close the front cover of the finisher.
CAUTION
When closing the front cover of the finisher, be careful not to get your fingers caught, as this may result in personal injury.
NOTE
After the cover is closed, the stapler unit may automatically perform a "dry" stapling operation to reposition the staples.
Back to Top