e-ManualTopSite mapHelp

Category Top

Loading Paper

Loading Paper into a Paper Drawer

Adjusting a Paper Drawer to Hold a Different Paper Size

Loading Envelopes

Loading Pre-Punched Paper

Loading Transparencies/Clear Film

Loading Tab Paper

Loading Paper into the POD Deck Lite-B1 (Optional)

Loading Paper into the Multi-drawer Paper Deck-B1 (Optional)

Loading Paper into the Document Insertion Unit-M1 (Optional)

Replacing the Staple Cartridge (For Optional Products)

Replacing the Staple Cartridge in the Stapler Unit (Finisher-AM1/Saddle Finisher-AM2)

Replacing the Staple Cartridge in the Saddle Stitcher Unit (Saddle Finisher-AM2)

Replacing the Staple Cartridge in the Stapler Unit (Staple Finisher-T1/Booklet Finisher-T1)

Replacing the Staple Case in the Saddle Stitcher Unit (Booklet Finisher-T1)

Removing Staple Waste (Finisher-AM1/Saddle Finisher-AM2)

Removing Punch Waste (Puncher Unit-BS1/Puncher Unit-BT1)

Removing Punch Waste (External 2/3 Hole Puncher-C1/External 2/4 Hole Puncher-C1/External 4 Hole Puncher-C1)

Operating the Limited Functions Mode

Replacing the Toner Cartridge

Replacing the Waste Toner Container

Routine Cleaning

Originals Cannot Be Scanned Properly (Cleaning the Platen Glass)

Originals Cannot Be Scanned Properly (Cleaning Method of the Original Scanning Area)

Scanned Originals Become Dirty (Manual Feeder Cleaning)

Scanned Originals Become Dirty (Automatic Feeder Cleaning)

Output Paper Becomes Dirty (Cleaning Inside of the Main Unit)

Output Paper Becomes Dirty (Wire Cleaning)

Output Paper Becomes Dirty (Roller Cleaning)

Output Paper Becomes Dirty (Belt Cleaning)

Streaks and Gloss Unevenness Appear on Output Paper (Refreshing the Fixing Belt)

Streaks and Gloss Unevenness Appear on Output Paper (Adjusting the Fixing Belt Auto Refresh Level)

Cleaning the Touch Panel Display

Consumables

Top » Maintenance » Removing Punch Waste (External 2/3 Hole Puncher-C1/External 2/4 Hole Puncher-C1/External 4 Hole Puncher-C1)
Removing Punch Waste (External 2/3 Hole Puncher-C1/External 2/4 Hole Puncher-C1/External 4 Hole Puncher-C1)
0L3X-0LS
When the punch waste tray of the External 2/3 Hole Puncher-C1 or External 2/4 Hole Puncher-C1 or External 4 Hole Puncher-C1 becomes full, an animation screen prompting you to remove the punch waste appears on the touch panel display.
The location of the External 2/3 Hole Puncher-C1 or External 2/4 Hole Puncher-C1 or External 4 Hole Puncher-C1 is indicated in the following illustration.
NOTE
The External 2/3 Hole Puncher-C1, External 2/4 Hole Puncher-C1 and External 4 Hole Puncher-C1 are optional products.
The External 2/3 Hole Puncher-C1/External 2/4 Hole Puncher-C1/External 4 Hole Puncher-C1 is available only when the Staple Finisher-T1 or Booklet Finisher-T1 is attached.
1.
Pull out the punch waste tray.
1. Open the front cover of the puncher.
2. Pull out the punch waste tray.
2.
Discard the punch waste.
NOTE
Make sure that the punch waste tray is completely emptied.
3.
Return the punch waste tray to its original position.
1. Push the punch waste tray back into its original position.
2. Close the front cover of the puncher.
CAUTION
When closing the cover, be careful not to get your fingers caught, as this may result in personal injury.
NOTE
If the punch waste tray is not securely in place, you cannot make copies or prints in the Hole Punch mode.
Back to Top