<Adjust Action>

This section describes the copy and print finishing settings, such as adjusting the saddle stitch position.

<Saddle Stitch Staple Repositioning>

Feeds papers to the saddle stitcher unit and staple them several times, and performs the saddle stitch staple repositioning procedure. The machine performs this adjustment procedure after you clear a paper jam or replace the staple cartridge.


Only use 13" x 19", 12 5/8" x 17 11/16", 12" x 18", A3, B4, A4R, 11" x 17", LGL, or LTRR paper for the saddle stitch staple repositioning procedure. Make sure to remove all output booklets from the booklet tray before performing the saddle stitch staple repositioning procedure. Make sure to remove the paper that was used for adjustment.


Paper that is required for the saddle stitch staple repositioning procedure is automatically fed to the saddle stitcher unit by the machine.

<Change Fold/Stitch Position>

If you notice that the saddle stitch position of the paper is not exactly in the middle of the booklet, you can make adjustments to the saddle stitch position to compensate for this error. Adjust the folding position of the paper and the saddle stitch position at the same time. Adjusting the Saddle Stitch Position

<Adjust Saddle Stitch Fold Position>

If you notice that the folds of the paper are not exactly in the middle of the booklet, you can make adjustments to the fold placement to compensate for this error. This mode enables you to adjust the folding position without changing the stapling position. Adjusting the Saddle Stitch Folding Position

<Adjust Double Staple Width>

You can adjust the double staple width.


When the paper width is smaller than 10 1/8" (257 mm), double staple width is fixed <4_3/4">.

<Switch Finisher Puncher Mode>

You can set whether to give priority to the punching speed or to precision.

<Speed/Precision Priority for Double Staple>

You can set whether to give priority to the double stapling speed or to precision.


This mode is enabled only when using the following paper: Paper size: The width for the feeding direction is 8 1/2" (215.9 mm) or less Paper type: Plain, Heavy 1, Color, Pre-punched Paper weight: 17 lb bond to 32 lb bond (64 g/m2 to 128 g/m2) If you select <Speed Priority>, stapled output paper may not be aligned due to the temperature, humidity, or characteristics of the paper type.

<Adjust Trim Width>

You can adjust the trimming width of Saddle Stitch printouts in 0.01" increments. When using the optional Booklet Trimmer-D1, also see the included instruction manual for more information.

<Adjust Fold Position>

You can adjust the paper folding position. Adjusting the Paper Folding Position

<Alignment Adjustment When Stapling>

The copied or printed paper may shrink because of temperature, humidity, or a characteristic of the paper type. In this case, this mode enables you to align copied or printed papers by adjusting the position of the alignment guide inside the finisher so as to staple the aligned papers.


If the alignment guide's position is too close to the paper, a paper jam or paper crease may occur. Make sure to perform fine adjustment of the alignment guide's position.

<Finisher Tray A Alignment Adjustment>

You can adjust paper alignment when outputting to Tray A of a finisher. Adjusting Paper Alignment


You cannot align output paper in the following situations: when using paper smaller than STMTR when using different size paper together If you set <Align Output Paper of Diff. Sizes (Diff. Widths)>to <On>, you can align output paper by paper width.


You can switch between positive and negative values by pressing <±>.

<Finisher Tray B Alignment Adjustment>

You can adjust paper alignment when outputting to Tray B of a finisher. Adjusting Paper Alignment


You cannot align output paper in the following situations: when using paper smaller than STMTR when using different size paper together If you set <Align Output Paper of Diff. Sizes (Diff. Widths)to <On>, you can align output paper by paper width.


You can switch between positive and negative values by pressing <±>.

<Finisher Output Priority Settings (Heavy 1-4)>

You can give priority to productivity or alignment for the output paper when using <Heavy 1>, <Heavy 2>, <Heavy 3>, or <Heavy 4>.

<Finisher Output Priority Settings (Heavy 5, 6)>

You can give priority to productivity or alignment for the output paper when using <Heavy 5> or <Heavy 6>.

<Finisher Output Priority Settings (Thin)>

You can give priority to productivity or alignment for the output paper when using thin paper.


<Alignment Priority> is available only when outputting on Tray B of a finisher.

<Time Until Stapling Starts in Stapler Mode>

You can set the time until stapling is performed after inserting paper when using manual stapling.